00050 / 00150
TS - Tapered Single (12.700x38.100x13.500)
Bearing Data
Key Dimensions
| Parameters | Value | Units |
|---|---|---|
| Cone Part Number | 00050 | - |
| Cup Part Number | 00150 | - |
| Bore (d) | 12.700 | mm |
| O.D. (D) | 38.100 | mm |
| Width (T) | 13.500 | mm |
|
Dynamic Radial Load Rating - 1M Revs (C1)
The Timken basic dynamic radial load rating for an L10 life of 1 million revolutions
|
20,900 | N |
|
Dynamic Radial Load Rating - 90M Revs (C90)
The Timken basic dynamic radial load rating for an L10 life of 90 million revolutions
|
5,410 | N |
|
e Factor
Limiting value for Fa/ Fr for the applicability of different values of the factors X and Y in the dynamic equivalent radial load calculation
|
0.28 | - |
|
K Factor
The minimum ratio of basic dynamic radial load rating to basic dynamic thrust load rating in a single-row tapered roller bearing
|
2.12 | - |
Other Dimensions
| Parameters | Value | Units |
|---|---|---|
| Weight | 0.08 | kg |
| Inner Ring Width (B) | 14.072 | mm |
| Outer Ring Width (C) | 11.112 | mm |
|
Effective Center Location
The point at which the lines of force normal to the outer ring raceway intersect the bearing axis of a tapered roller bearing
|
-5.1 | mm |
| Max Shaft Fillet Radius | 1.5 | mm |
| Max Housing Fillet Radius | 0.8 | mm |
| Shaft Backing Shoulder Diameter - Frontface (da) | 16.5 | mm |
| Shaft Backing Shoulder Diameter - Backface (db) | 19.0 | mm |
| Housing Backing Shoulder Diameter - Frontface (Da) | 34.0 | mm |
| Housing Backing Shoulder Diameter - Backface (Db) | 33.0 | mm |
|
Cage Location Relative to Backface (Aa)
A positive value means the cage is inside the cone backface and a negative value means the cage is outside the cone backface
|
-0.8 | mm |
|
Cage Location Relative to Frontface (Ab)
A positive value means the cage is outside the cone frontface and a negative value means the cage is inside the cone frontface
|
2.0 | mm |
Ratings
| Parameters | Value | Units |
|---|---|---|
|
Dynamic Radial Load Rating - 1M Revs (C1)
The Timken basic dynamic radial load rating for an L10 life of 1 million revolutions
|
20,900 | N |
|
Dynamic Radial Load Rating - 90M Revs (C90)
The Timken basic dynamic radial load rating for an L10 life of 90 million revolutions
|
5,410 | N |
|
Dynamic Axial Rating - 90M Revs (Ca90)
The Timken basic dynamic axial load rating for an L10 life of 90 million revolutions
|
2,550 | N |
| Static Radial Load Rating (C0) | 17,100 | N |
Factors
| Parameters | Value | Units |
|---|---|---|
|
Y Factor
The maximum recommended thrust load which should be applied to the bearing while in motion
|
2.18 | - |
|
G1 Factor
Geometry factor used to calculate bearing torque and heat generation
|
3.1 | - |
|
G2 Factor
Geometry factor used to calculate bearing torque and heat generation
|
2.9 | - |
|
Geometry Factor (Cg)
Geometry factor used to calculate the catalog a3l factor
|
0.0330 | - |
Disclaimer: The accuracy of this technical review is dependent upon the validity and the completeness of information supplied to Timken. Actual product performance is affected by many factors beyond the control of Timken. Therefore, the suitability and feasibility of all designs and product selection should be validated by you. For the above reasons, this review is submitted solely to provide you, a customer of Timken or its parent or affiliates, with data to assist you in your design. No warranty, expressed or implied, including any warranty of fitness for a particular purpose, is made by Timken by the submission of this review. Timken products are sold subject to Limited Warranty which is set forth in Timken’s terms and conditions of sale.